Metra XSVI-6522 Manuale di Installazione Scaricare il pdf

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE: The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522:

Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORA

TION

XSVI-6522

INSTALLATION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE: The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522:

Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORATION

XSVI-6522

INSTALLATION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE: The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522: Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORA

TION

XSVI-6522

INSTALLATION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE: The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522:

Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORATION

XSVI-6522

INSTALLATION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE:

The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO:

With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522: Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORA

TION

XSVI-6522

INSTALLATION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE: The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522:

Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORA

TION

XSVI-6522

INSTALLATION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE:

The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERF

ACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522: Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORA

TION

XSVI-6522

INSTALLA

TION INSTRUCTIONS

In the Dodge and Jeep vehicles listed below there are

no 12 volt accessory wires currently in the factory har-

ness making the installer run an accessory wire to the

fuse box or underneath the steering column when

installing an aftermarket radio. The XSVI-6522 is

designed to provide a 12 volt 10 amp switched acces-

sory output along with the rest of the wires needed to

install an aftermarket radio. The R.A.P. (Retained

Accessory Power) function, where power is supplied to

the radio after the ignition is shut off until one of the

front doors are opened, is retained by the XSVI-6522.

TE: The XSVI-6522 does not retain use of the fac-

tory amplifier if so equipped. INITIALIZE THE XSVI

INTERFACE BEFORE TURNING ON RADIO: With all

connections made and harnesses connected to the

vehicle, turn ignition key to the ON position for thir-

ty seconds, then turn key off.

Wiring the XSVI-6522:

Wiring up the XSVI-6522 is like

wiring up any other wire harness that would attach to

the aftermarket radios harness.The Metra/EIA wire

code can be found on the back of this package that will

aid you in the wiring of your aftermarket radio.

(See Applications on back of page)

INSTXSVI-6522 Rev. 03/12/10

1-800-221-0932 www.metraonline.com

METRA ELECTRONICS CORPORA

TION

XSVI-6522

INSTALLATION INSTRUCTIONS

1 2

Sommario

Pagina 1

In the Dodge and Jeep vehicles listed below there areno 12 volt accessory wires currently in the factory har-ness making the installer run an accessor

Pagina 2

Commenti su questo manuale

Nessun commento

Metra XSVI-6522 Manuale di Installazione

Navigare online o scaricare Manuale di Installazione per Gruppi di connettori elettrici Metra XSVI-6522. Metra XSVI-6522 electrical connector assembly Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Gruppi di connettori elettrici Metra XSVI-6522